Epson T0712/T0892 Cyan


  • Stylus D78
  • Stylus D92
  • Stylus D120
  • Stylus DX4000
  • Stylus DX4050
  • Stylus DX4400
  • Stylus DX4450
  • Stylus DX5000
  • Stylus DX5050
  • Stylus DX6000
  • Stylus DX6050
  • Stylus DX7000F
  • Stylus DX7400
  • Stylus DX7450
  • Stylus DX8400
  • Stylus DX8450
  • Stylus DX9400F
  • Stylus S20
  • Stylus S21
  • Stylus SX100
  • Stylus SX105
  • Stylus SX110
  • Stylus SX115
  • Stylus SX200
  • Stylus SX205
  • Stylus SX210
  • Stylus SX215
  • Stylus SX218
  • Stylus SX400
  • Stylus SX405
  • Stylus SX410
  • Stylus SX415
  • Stylus SX510W
  • Stylus SX515W
  • Stylus SX600FW
  • Stylus SX610FW
  • Stylus BX300F
  • Stylus BX310
  • Stylus BX600FW
  • Stylus BX610FW
  • Stylus B40W


After single or multiple cartridge installations, the printer performs an automatic cleaning cycle which removes ink from all the cartridges. This process may result in an existing cartridge becoming empty.
Was this answer helpful?
Perform a print head cleaning cycle. This can be located within the printer maintenance menu. Print a nozzle check to see if all the nozzles are free of blockages. If breaks still appear on the printed page, repeat the process. If the nozzle check page displays one set of black nozzles shown below, only perform up to two cleans.
If the screen displays up to three sets of nozzles, perform up to three cleans: 99% of all blocked nozzles are caused by trapped air within the print head. If the cleaning cycle does not remove the lines, rest the printer for half an hour and perform a nozzle check. (Do not continue to clean the cartridges as this will use up valuable ink from all the cartridges).
If there is no improvement, leave the cartridge for a further two hours. During the rest period, ink from the cartridge will migrate through the cartridge and absorb / push trapped air from the print head.
If Epson cartridges are removed from the printer for any length of time, the print head is liable to dry out and block up. Always remove used cartridges when you have a replacement available.
Never remove the power supply when the printer is in operation such as paper feed, cleaning cycle and printing. When the printer is not in use, the print head will park over the ‘capping mechanism’ which seals over the print head preventing it from drying out.
Was this answer helpful?
It is possible that one of the cartridge chips has not connected properly with one of the printer electrical contacts. The printer carriage needs to be placed in the cartridge change position. This can be achieved by either pressing the ink / OK button on the printer or following the step by step cartridge change guide located within the printer maintenance menu
Lift the cartridge location lever and push your finger firmly on the top of the cartridges. If this fails, carefully lift the affected cartridge without breaking the rubber seal at the bottom of the product. Push firmly back into position to re-engage the chip / printer contacts.
Was this answer helpful?
Please remove the cartridge from the printer and using a clean tissue gently wipe the chip.
Was this answer helpful?

1.Shake cartridge 3 times and remove

yellow tape (if applicable).

2.Remove coloured cap and install


3.When you install a cartridge a

message may appear advising

you that the cartridge is a

non-genuine ink cartridge.

4.This cartridge is not empty and

has been refilled.

5.Follow on-screen instructions

to continue.

6.The ink status monitor will

show that the cartridge is full.

7.Following installation peform a Head

Cleaning operation using the status

monitor or printer display (as per

your printers instructions).

Was this answer helpful?