Samsung ML-2010D3 - Ink Support

COMPATIBLE WITH

ML-2010

Troubleshooting - Click each question for details

Do I shake the cartridge prior to installation to my printer?

Your cartridge contains very fine powder called ‘toner’. Prior to installation gently rock the cartridge from side to side 2 to 3 times to allow the powder to move into position before printing. You will not need to repeat this process once the cartridge is installed as most cartridges contain a mechanical paddle which agitates the powder during the printing process.

Was this answer helpful?

I have used a remanufactured cartridge before and the drum was a different colour

Prior to remanufacturing the cartridge, each product is tested to ensure the drum, usually a dull blue/green colour, is in a good condition. Original drums are very versatile and can in some cases be repeatedly used.

If the original drum has been damaged during the collection and recovery process, a new drum will be fitted which will usually be a shiny light green colour.

Was this answer helpful?

I have installed the cartridge and the toner level indicator is not active

To avoid patent infringements the design of the memory chip may differ from the original product. Some laser toner cartridges when installed will not display the memory status bar of your printer display. This does not affect the performance of the cartridge and you may continue to print.

Was this answer helpful?

I have installed my cartridge and received an error that the cartridge is missing or faulty

Remove the cartridge from the printer and while the printer is still on, remove the power by switching off the printer at the socket. Leave the printer for 10 minutes to allow all power to drain and the error to clear.

In the meantime, find the chip on your cartridge and give it a wipe with some tissue to make sure there is no ink or dust interfering in the communication between the cartridge and the printer.

After 10 minutes, switch your printer back on and re-install the cartridge.

If this did not resolve your problem then unfortunately the cartridge is faulty and should be returned to your store.

Was this answer helpful?

My cartridge will no longer print

Some laser toner cartridges are fitted with a memory chip which prevents the cartridge working once the chip has reached the end of its pre-set counter. This chip cannot be reset.

Please note that some chips are radio frequency devices and are fitted to the interior of the cartridge and cannot be visually detected.

Was this answer helpful?

When I print there are dots repeatedly appearing in the same location down the length of the page

A small amount of toner powder has fallen onto an internal component of the cartridge. This powder can be removed either by running a printer calibration which will clean the component, or by printing a few normal pages which will naturally clear through the small amount of toner. Once done, the dots should no longer appear on the page while printing.

Was this answer helpful?

I have removed a used cartridge from my printer and a small amount of toner has leaked out

Many cartridges have a waste tank to collect the paper dust and toner powder during cleaning cycles. Powder from this waste tank can sometimes be shaken loose when you remove your cartridge from the printer.

Was this answer helpful?

How do I clear up toner powder?

In the unlikely event toner powder is deposited onto a work surface, wipe away with a damp disposable tissue. Always unplug the printer from the power supply before cleaning your printer.

To remove toner from your hands use cold water with mild household soap. Do not use warm or hot water as this will fuse the toner to your skin.

Was this answer helpful?

Should I update my printer firmware?

Printer manufacturers often use the roll out of their printer firmware updates to prevent you from choosing the origin and type of supplies you use in your printer. This has been done is ways such as blocking the use of remanufactured/recycled cartridges entirely, applying a 'cartridge lock' system that locks a cartridge's usage to a printer and introducing a new 'generation' of the same cartridge model to stop older, remanufactured cartridges being re-used.

Most printer manufacturers will prefer you to set your printer to automatically download and install their updates for this very reason. We suggest that you disable the automatic update option to allow you to continue to use remanufactured cartridges and also to recycle your cartridge after it has been used. By allowing your printer to update the firmware automatically you are risking being locked into only using the more expensive and less environmentally friendly original branded cartridges.

So we highly recommend switching off your printer's firmware automatic updates and dismissing future messages asking you to update your printer. These steps are a general guide to how to stop the updates, but please note that they will vary slightly depending on your exact printer model.

Was this answer helpful?